Denon Stereo Receiver Denon AVR-E400 Integrated Network AV Receiver User Manual

0

Out of 0 Ratings

Owner's of the Denon Stereo Receiver Denon AVR-E400 Integrated Network AV Receiver gave it a score of 0 out of 5. Here's how the scores stacked up:

  • Reliability

    0 out of 5

  • Durability

    0 out of 5

  • Maintenance

    0 out of 5

  • Performance

    0 out of 5

  • Ease of Use

    0 out of 5
of 159
 
104
Audio
Volume
Default settings are underlined.
Set the MAIN ZONE (room where the unit is located) volume setting.
Setting items Setting details
Scale
Set how volume is
displayed.
0 – 98 : Display in the range 0 (Min) to 98.
–79.5dB – 18.0dB : Display ---dB (Min), in the range –79.5 dB to 18.0 dB.
•The “Scale” setting is applied also to the “Limit” and “Power On Level”
display method.
•The “Scale” setting applies to all zones.
Limit
Make a setting for
maximum volume.
60 (–20dB) / 70 (–10dB) / 80 (0dB)
O : Do not set a maximum volume.
Power On Level
Define the volume setting
that is active when the
power is turned on.
Last : Use the memorized setting from the last session.
Mute : Always use the muting on condition when power is turned on.
1 – 98 (–79dB – 18dB) : The volume is adjusted to the set level.
Mute Level
Set the amount of
attenuation when muting
is on.
Full : The sound is muted entirely.
–40dB : The sound is attenuated by 40 dB down.
–20dB : The sound is attenuated by 20 dB down.
Audyssey
Default settings are underlined.
Set Audyssey MultEQ
®
, Audyssey Dynamic EQ
®
and Audyssey Dynamic Volume
®
. These can be selected
after Audyssey
®
Setup has been performed. For additional information on Audyssey technology, please
see page142.
NOTE
•If you have not performed Audyssey
®
Setup, or if you change the speaker settings after performing
Audyssey
®
Setup, you may not be able to select Dynamic EQ/Dynamic Volume.
In this case, either perform Audyssey
®
Setup over again or perform “Restore...” (vpage27) to return
to the settings after Audyssey
®
Setup was run.
•When HD Audio for which the sampling frequency exceeds 96 kHz is played back, the “Audyssey”
cannot be set.
Setting items Setting details
MultEQ
®
MultEQ
®
compensates for
both time and frequency
characteristics of the
listening area based on
Audyssey
®
Setup
measurement results.
Selection is done from three
types of compensation
curves. We recommend the
“Audyssey” setting.
MultEQ
®
is the prerequisite
function for Dynamic EQ
and Dynamic Volume.
Audyssey : Optimize the frequency response of all speakers.
Audyssey Byp.L/R : Optimize frequency response of speakers except
front L and R speakers.
Audyssey Flat : Optimize frequency response of all speakers to flat
response.
Graphic EQ : Apply frequency response set with “Graphic EQ”
(vpage105).
O : Turn “MultEQ
®
” equalizer o.
“Audyssey”, “Audyssey Byp.L/R” and “Audyssey Flat” can be selected
after Audyssey
®
Setup has been performed. “Audyssey” is automatically
selected after performing Audyssey
®
Setup. When “Audyssey”, “Audyssey
Byp.L/R” or “Audyssey Flat” is selected, illuminates.
NOTE
When using headphones, “MultEQ
®
” is automatically set to “O”.
“MultEQ
®
”, “Dynamic EQ” and “Dynamic Volume” settings are stored for each input source.
Basic instructions
Advanced instructions
Information
Advanced instructions
v See overleaf
DVD

   Find Your Products By Category